Bobst Novacut 106 ER

TECHNICAL FEATURES PROCESSED MATERIALS

Paper (according to quality), min 80 g/m2

Carton (depending on quality), up to (*) 2000 g/m2

Corrugated cardboard (micro-corrugated), up to (*) 4 mm (*)

Permissible cardboard warping: 4% of the sheet width

FORMATS

Embossing, max 1060 x 730 mm

Sheet size, max. 1060 x 760 mm

Sheet size, min. 400 x 350 mm

Punch full size, max. 1070 x 770 mm

DIE-CUTTING FORMAT With front trim, max. 1060 x 746 mm

SIZE OF PALLETS Feeder/output, max. 1200 x 800 mm

DIE-CUTTING Gripper strip 9 -17 mm

Cutting thread height 23.8 mm

Double-cut thickness 5 mm

PRODUCTION

Die-cutting force, max 2.6 (260 t.) MN

Hourly speed, up to (f/h) 7000

PILE HEIGHT

Feeder in normal position, max 1820 mm

Sheet feeder in Non-Stop position, max 1520 mm

Max output 1550 mm

Standard Equipment

MACHINE

• Platform with safety barriers

• Machine equipped with e-VIEW system

• Centerline system for quick job changeover

• Electronic sheet travel control device with automatic sensitivity adjustment based on the

processed materials, including transparent materials, and photocells for the automatic cycle at the

feeder and delivery

• Adjustable register centring at the stripper and blank separator (upper, central, and lower) with

indicators

• C.U.B.E.3 system (Control Unit Bobst Electronic) with color touch screen for machine

management. This microprocessor-controlled system, developed by Bobst, allows the operator to

easily control the machine, as well as display and verify the various machine functions and

elements.

FEEDER

• Pile tray with manual lateral pile correction during production

• Sheet synchronizer to adjust sheet arrival at the front registers, viewable on the CUBE3 display.

Adjustable while the machine is running for platen fine-tuning. It facilitates the timing of sheet

arrival to compensate for variations in different processed paperboards.

• Pile height control via feeler foot

• Adjustable side blowers

• Suction unit with multiple adjustmentsFEED TABLE

• Covered with an antistatic stainless steel plate

• Feed table introduction with lateral ramps

• 4 adjustable front registers with sheet presence control via fiber optic control system

• Operator side or opposite operator side pull guide, adjustable with Centerline references.

Convertible to push guide, with electro-optical control system.

• Sheet hold-down device (sheet guide into gripper bar)

• Upper frame with pneumatic lifting device

• Upper transport equipment for paper and corrugated board

• 2 transport belts with lateral guide and automatic tensioning system

PLATEN PRESS

• Gripper bar reopening device

• Centring and locking of die-cutting equipment

• Automatic frame locking towards the upper block

• Cutting force measurement via load gauge

• Motorized device for cutting force adjustment

• Synthetic material supporting plate, 12 mm thickness

STRIPPING STATION

• Quick-lock device for the central board

• Integrated quick-locking system: automatic quick-locking device for the upper tool integrated into

the machine

• Adjustable centring on all equipment (upper, central, and lower)

BLANKING STATION (BLANK SEPARATION)

• Automatic sheet insertion device with electrical sheet presence control

• Automatic suction cup selection according to sheet size

• Constant level pile adjustment (NCT)

• Continuous pile lowering while keeping the top of the pile at a constant height

• Automatic Non-Stop device

• Pile lifting safety device

• Waste or residual grid evacuation conveyor belt

• Integrated quick-locking system: automatic quick-locking device for the upper tool integrated into

the machine

• Adjustable centring for all equipment (upper, lower)

• Lower drawer frame with fixing material

EQUIPMENT

• 1 Quick-lock upper frame: fixed bottom (T-103.001), 2 mm thickness bottom plate and 1 mm

thickness synthetic make-ready protection plate

• 1 Cutting plate (T-120.001)

• 1 Lower stripping drawer frame (T-230.001)

• 1 Lower stripping equipment (T-235.001): waste stripping equipment, including bars and telescopic

needles

Equipped with

AUTOMATIC PALLET CHANGING DEVICE

Complete pile removal (OOS) and automatic introduction of the empty pallet to allow a continuous

production cycle. Device mounted above floor level (maximum height reduced by 100mm; requires a ramp,

supplied by the customer) or recessed with pile from the floor.

QUICK-LOCK UPPER FRAME: FIXED BOTTOM2 mm thickness bottom plate and 1 mm thickness synthetic make-ready protection plate. Valid with std IIIb

dim 1040x725 / std 104 = 1050x744 / std. 106 = 1070x770mm. 1 unit is included in the standard equipment.

UPPER DRAWER FRAME

Can be used in machines with a quick-locking device.

UPPER STRIPPING EQUIPMENT

Equipment required for making a stripping tool, including bars, fixing clamps, stripping holders, and a set of

stripping pins with diameters of 3, 5, and 10 mm. This equipment mounts on the drawer frame (T-200.001).

UPPER BLANK SEPARATION DRAWER FRAME

UNIVERSAL UPPER BLANK SEPARATION TOOL

Equipment required for making a blank separation tool. This equipment mounts on the drawer frame (T-

300.001).

HELPLINE PLUS

Free support service during the machine warranty period with tacit renewal from year to year at the

indicated price. Both parties have the right to terminate the contract 60 days prior to the annual expiration

date. It is the customer's responsibility to refer to the technical specifications listed on the relevant Connect

pre-installation sheet.

CONNECT READY

Hardware and software required for connection to e-Services.